View NCV427407_1287949.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCV4274, NCV4274A 400 mA 2% and 4%Voltage Regulator Family
Description
The NCV4274 and NCV4274A is a precision micro-power voltage regulator with an output current capability of 400 mA available in the DPAK and D2PAK packages. The output voltage is accurate within 2.0% or 4.0% depending on the version with a maximum dropout voltage of 0.5 V with an input up to 40 V. Low quiescent current is a feature drawing only 150 mA with a 1 mA load. This part is ideal for automotive and all battery operated microprocessor equipment. The regulator is protected against reverse battery, short circuit, and thermal overload conditions. The device can withstand load dump transients making it suitable for use in automotive environments.
Features
http://onsemi.com MARKING DIAGRAMS
4 74X-xxG ALYWW x 1 2 3 1 Input 2, 4 Ground 3 Output
DPAK DT SUFFIX CASE 369C
* * * * *
* * * *
2.5, 3.3 V, 5.0 V, 2.0% and 4.0% Output Options Low 150 mA Quiescent Current at 1 mA load current 400 mA Output Current Capability Fault Protection +60 V Peak Transient Voltage with Respect to GND S -40 V Reverse Voltage S Short Circuit S Thermal Overload Very Low Dropout Voltage AEC-Q100 Qualified NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes These are Pb-Free Devices
4 NC V4274X-xx AWLYWWG D2PAK DS SUFFIX CASE 418AF
1 Input 2, 4 Ground 3 Output
1
2 4
3
SOT-223 ST SUFFIX CASE 318E X xx A L, WL Y WW, W G
AYW 74X-xxG 1 2 3
1 Input 2, 4 Ground 3 Output
= A or blank = Voltage Ratings = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 13 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2007
February, 2007 - Rev. 8
1
Publication Order Number: NCV4274/D
NCV4274, NCV4274A
I Q
Bandgap Refernece
- +
Current Limit and Saturation Sense
Thermal Shutdown
GND
Figure 1. Block Diagram
Pin Definitions and Functions
Pin No. 1 2,4 3 Symbol I GND Q Function Input; Bypass directly at the IC a ceramic capacitor to GND. Ground Output; Bypass with a capacitor to GND.
1. DPAK 3LD package code 6025 2. D2PAK 3LD package code 6083
ABSOLUTE MAXIMUM RATINGS
Pin Symbol, Parameter I, Input-to-Regulator Voltage Current I, Input peak Transient Voltage to Regulator with Respect to GND Q, Regulated Output Voltage Current GND, Ground Current Junction Temperature Storage Temperature ESD Capability, Human Body Model ESD Capability, Machine Model ESD Capability, Charged Device Model Symbol VI II VI VQ IQ IGND TJ TStg ESDHB ESDMM ESDCDM -1.0 Internally Limited - - -50 4 200 1 Condition Min -42 Internally Limited Max 45 Internally Limited 60 40 Internally Limited 100 150 150 mA C C kV V kV V V Unit V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 3. This device series incorporates ESD protection and is tested by the following methods: ESD HBM tested per AEC-Q100-002 (EIA/JESD22-A114) ESD MM tested per AEC-Q100-003 (EIA/JESD22-A115) ESD CDM tested per EIA/JES D22/C101, Field Induced Charge Model
http://onsemi.com
2
NCV4274, NCV4274A
OPERATING RANGE
Parameter Input Voltage (5.0 V Version) Input Voltage (3.3 V, and 2.5 V Version) Junction Temperature Symbol VI VI TJ Condition Min 5.5 4.5 -40 Max 40 40 150 Unit V V C
THERMAL RESISTANCE
Parameter Junction-to-Ambient Junction-to-Ambient Junction-to-Case Junction-to-Case Junction-to-Tab Junction-to-Ambient 4. Soldered in, minimal footprint, FR4 5. 1 oz copper, 5 mm2 copper area, FR4 DPAK D2PAK DPAK D2PAK SOT-223 SOT-223 Symbol Rthja Rthja Rthjc Rthjc Y-JLX,
YLX
Condition
Min - - - - - -
Max 70 (Note 4) 60 (Note 4) 4 3 14.5 (Note 5) 169.7 (Note 5)
Unit C/W C/W C/W C/W C/W C/W
RqJA, qJA
LEAD FREE SOLDERING TEMPERATURE AND MSL
Parameter Lead Free Soldering, (Note 6) Reflow (SMD styles only), Moisture Sensitivity Level 6. Per IPC/JEDEC J-STD-020C Pb-Free Symbol Tsld Condition 60s - 150s Above 217s 40s Max at Peak DPAK and D2PAK SOT-223 Min - 1 3 Max 265 pk - - Unit C
MSL
http://onsemi.com
3
NCV4274, NCV4274A
ELECTRICAL CHARACTERISTICS NCV4274A and NCV4274 5.0 V -40C < TJ < 150C; VI = 13.5 V unless otherwise noted. Min Parameter REGULATOR Output Voltage (5.0 V Version) Output Voltage (5.0 V Version) Output Voltage (3.3 V Version) Output Voltage (3.3 V Version) Output Voltage (2.5 V Version) Output Voltage (2.5 V Version) Current Limit Quiescent Current VQ VQ VQ VQ VQ VQ IQ Iq 5 mA < IQ < 400 mA 6V < VI < 28 V 5 mA < IQ < 200 mA 6 V < VI < 40 V 5 mA < IQ < 400 mA 4.5 V < VI < 28 V 5 mA < IQ < 200 mA 4.5 V < VI < 40 V 5 mA < IQ < 400 mA 4.5 V < VI < 28 V 5 mA < IQ < 200 mA 4.5 V < VI < 40 V - Iq = 1 mA VQ = 5.0 V VQ = 3.3 V VQ = 2.5 V Iq = 250 mA VQ = 5.0 V VQ = 3.3 V VQ = 2.5 V Iq = 400 mA VQ = 5.0 V VQ = 3.3 V VQ = 2.5 V IQ = 250 mA, VDR = VI - VQ VI = 5.0 V VI = 4.5 V VI = 4.5 V IQ = 5 mA to 400 mA DVI = 12 V to 32 V IQ = 5 mA r = 100 Hz, Vr = 0.5 VPP 4.9 4.9 3.23 3.23 2.45 2.45 400 - - - - - - - - - 5.0 5.0 3.3 3.3 2.5 2.5 600 190 145 140 10 13 12 20 30 28 5.1 5.1 3.37 3.37 2.55 2.55 - 250 250 250 15 20 15 35 45 35 4.8 4.8 3.17 3.17 2.4 2.4 400 - - - - - - - - - 5.0 5.0 3.3 3.3 2.5 2.5 600 190 145 140 10 13 12 20 30 28 5.2 5.2 3.43 3.43 2.6 2.6 - 250 250 250 15 20 15 35 45 35 V V V V V V mA mA mA mA mA mA mA mA mA mA Symbol Test Conditions Typ Max Min Typ Max Unit
NCV4274A
NCV4274
Dropout Voltage 5.0 V Version 3.3 V Version 2.5 V Version Load Regulation Line Regulation Power Supply Ripple Rejection Temperature output voltage drift Thermal Shutdown Temperature* *Guaranteed by design, not tested in production VI VI II C11 1.0 mF I C12 100 nF 1 NCV4274 3 NCV4274A 2,4 GND IGND Q
VDR
- - - - - - -
250 - - 7 10 60 0.5 -
500 1.23 2.05 20 25 - - 210
- - - - - - - 165
250 - - 7 10 60 0.5 -
500 1.33 2.1 30 25 - - 210
mV V V mV mV dB mV/K C
DVQ DVQ PSRR dVQ/dT TSD
IQ = 5 mA
165
IQ CQ 10 mF or 22 mF
VQ VQ
4.5 - 40 V Input Rload CI 100 nF
1
NCV4274 3 NCV4274A 2,4 GND
5.0 V CQ Output 10 mF
Figure 2. Measuring Circuit
Figure 3. Application Circuit
http://onsemi.com
4
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES
1000 VI = 13.5 V 100 ESR (W) Maximum ESR COUT = 1 mF - 100 mF Stable Region Minimum ESR COUT = 1 mF 0 5 20 60 100 140 180 220 260 300 340 380 420 LOAD CURRENT (mA)
10
1.0
0.1
Figure 4. ESR Characterization
http://onsemi.com
5
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES - 5.0 V Version
5.2 VI = 13.5 V RL = 1 kW 5.1 4 VQ (V) 5.0 VQ (V) 3 2 4.9 1 4.8 -40 0 0 40 TJ (C) 80 120 160 0 2 4 VI (V) 6 8 10 6 5 RL = 20 W TJ = 25C
Figure 5. Output Voltage vs. Junction Temperature
Figure 6. Output Voltage vs. Input Voltage
800 TJ = 25C VQ = 0 V 600
60 50 40 TJ = 25C VI = 13.5 V
IQ (mA)
Iq (mA)
400
30 20
200 10 0 0 0 10 20 VI (V) 30 40 50 0 100 200 300 IQ (mA) 400 500 600
Figure 7. Output Current vs. Input Voltage
1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 0 10 20 30 IQ (mA) 40 50 60 100 0 VDR (mV) Iq (mA) TJ = 25C VI = 13.5 V 600 500 400
Figure 8. Current Consumption vs. Output Current (High Load)
TJ = 125C 300 200 TJ = 25C
0
100
200 IQ (mA)
300
400
Figure 9. Current Consumption vs. Output Current (Low Load)
Figure 10. Drop Voltage vs. Output Current
http://onsemi.com
6
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES - 5.0 V Version
40 RL = 20 W TJ = 25C 30 Iq (mA) II (mA) 6 4 2 0 -2 20 -4 -6 -8 10 -10 -12 -14 0 0 10 20 VI (V) 30 40 50 -16 -50 -25 0 VI (V) 25 50 RL = 6.8 kW TJ = 25C
Figure 11. Current Consumption vs. Input Voltage
Figure 12. Input Current vs. Input Voltage
http://onsemi.com
7
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES - 3.3 V Version
3.5 3.4 3.3 VQ (V) 3.2 3.1 3.0 2.9 -40 VQ (V) VI = 6 V RL = 1 kW 6 5 4 3 2 1 0 0 40 TJ (C) 80 120 160 RL = 20 W TJ = 25C
0
1
2
3 VI (V)
4
5
6
Figure 13. Output Voltage vs. Junction Temperature
800 TJ = 25C VQ = 0 V 600 40 IQ (mA) Iq (mA) 400 30 20 200 10 0 0 0 60 50
Figure 14. Output Voltage vs. Input Voltage
TJ = 25C VI = 13.5 V
0
10
20 VI (V)
30
40
50
100
200
300 IQ (mA)
400
500
600
Figure 15. Output Current vs. Input Voltage
1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 10 20 30 IQ (mA) 40 50 60 1.16 1.14 VDR (V) Iq (mA) 1.22 1.20 1.18 TJ = 25C VI = 13.5 V 1.26 1.24
Figure 16. Current Consumption vs. Output Current (High Load)
TJ = 125C TJ = 25C
VDR = VI(min) - VQ
0
100
200 IQ (mA)
300
400
Figure 17. Current Consumption vs. Output Current (Low Load)
Figure 18. Voltage Drop vs. Output Current
http://onsemi.com
8
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES - 3.3 V Version
7 6 5 Iq (mA) II (mA) 4 3 2 1 0 0 10 20 VI (V) 30 40 50 RL = 20 W TJ = 25C 4 2 0 -2 -4 -6 -8 -10 -12 -14 -16 -50 -25 0 VI (V) RL = 3.3 kW TJ = 25C 25 50
Figure 19. Current Consumption vs. Input Voltage
Figure 20. Input Current vs. Input Voltage
http://onsemi.com
9
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES - 2.5 V Version
2.7 2.6 2.5 VQ (V) 2.4 2.3 2.2 2.1 -40 VQ (V) VI = 6 V RL = 1 kW 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 40 TJ (C) 80 120 160
0
1
2
3 VI (V)
4
5
6
Figure 21. Output Voltage vs. Junction Temperature
800 TJ = 25C VQ = 0 V 600 40 IQ (mA) Iq (mA) 400 30 20 200 10 0 0 0 60 50
Figure 22. Output Voltage vs. Input Voltage
TJ = 25C VI = 13.5 V
0
10
20 VI (V)
30
40
50
100
200
300 IQ (mA)
400
500
600
Figure 23. Output Current vs. Input Voltage
1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 10 20 30 IQ (mA) 40 50 60 VDR (V) Iq (mA) TJ = 25C VI = 13.5 V 2.05 2.04 2.03 2.02 2.01 2.00 1.99 1.98 1.97 1.96 1.95 0
Figure 24. Current Consumption vs. Output Current (High Load)
TJ = 125C TJ = 25C
VDR = VI(min) - VQ
100
200 IQ (mA)
300
400
Figure 25. Current Consumption vs. Output Current (Low Load)
Figure 26. Voltage Drop vs. Output Current
http://onsemi.com
10
NCV4274, NCV4274A
TYPICAL CHARACTERISTIC CURVES - 2.5 V Version
4.5 4.0 3.5 3.0 Iq (mA) 2.5 2.0 1.5 1.0 0.5 0 0 10 20 VI (V) 30 40 50 II (mA) RL = 20 W TJ = 25C 2 0 -2 -4 -6 -8 -10 -12 -14 -50 -25 0 VI (V) RL = 3.3 kW TJ = 25C 25 50
Figure 27. Current Consumption vs. Input Voltage
Figure 28. Input Current vs. Input Voltage
http://onsemi.com
11
NCV4274, NCV4274A
APPLICATION DESCRIPTION
Output Regulator
The output is controlled by a precision trimmed reference and error amplifier. The PNP output has saturation control for regulation while the input voltage is low, preventing over saturation. Current limit and voltage monitors complement the regulator design to give safe operating signals to the processor and control circuits.
Stability Considerations
Once the value of PD(max) is known, the maximum permissible value of RqJA can be calculated:
Pq
JA
+
150 C * T A PD
(eq. 2)
The input capacitor CI1 in Figure 2 is necessary for compensating input line reactance. Possible oscillations caused by input inductance and input capacitance can be damped by using a resistor of approximately 1 W in series with CI2. The output or compensation capacitor helps determine three main characteristics of a linear regulator: startup delay, load transient response and loop stability. The capacitor value and type should be based on cost, availability, size and temperature constraints. The aluminum electrolytic capacitor is the least expensive solution, but, if the circuit operates at low temperatures (-25C to -40C), both the value and ESR of the capacitor will vary considerably. The capacitor manufacturer's data sheet usually provides this information. The value for the output capacitor CQ shown in Figure 2 should work for most applications; however, it is not necessarily the optimized solution. Stability is guaranteed at values CQ w 2.2 mF and an ESR v 2.5 W within the operating temperature range. Actual limits are shown in a graph in the Typical Performance Characteristics section.
Calculating Power Dissipation in a Single Output Linear Regulator
The value of RqJA can then be compared with those in the package section of the data sheet. Those packages with RqJA's less than the calculated value in Equation 2 will keep the die temperature below 150C. In some cases, none of the packages will be sufficient to dissipate the heat generated by the IC, and an external heat sink will be required. The current flow and voltages are shown in the Measurement Circuit Diagram.
Heat Sinks
A heat sink effectively increases the surface area of the package to improve the flow of heat away from the IC and into the surrounding air. Each material in the heat flow path between the IC and the outside environment will have a thermal resistance. Like series electrical resistances, these resistances are summed to determine the value of RqJA:
R qJA + R qJC ) R qCS ) R qSA
(eq. 3)
The maximum power dissipation for a single output regulator (Figure 3) is:
P D(max) + [V I(max) * V Q(min)]I Q(max) ) V I(max)I q (eq. 1)
Where: RqJC = the junction-to-case thermal resistance, RqCS = the case-to-heat sink thermal resistance, and RqSA = the heat sink-to-ambient thermal resistance. RqJC appears in the package section of the data sheet. Like RqJA, it too is a function of package type. RqCS and RqSA are functions of the package type, heat sink and the interface between them. These values appear in data sheets of heat sink manufacturers. Thermal, mounting, and heat sinking are discussed in the ON Semiconductor application note AN1040/D, available on the ON Semiconductor Website.
Where: VI(max) is the maximum input voltage, VQ(min) is the minimum output voltage, IQ(max) is the maximum output current for the application, and Iq is the quiescent current the regulator consumes at IQ(max).
http://onsemi.com
12
NCV4274, NCV4274A
ORDERING INFORMATION4
Device NCV4274DS50G NCV4274DS50R4G NCV4274DT50G NCV4274DT50RKG NCV4274ADS50G NCV4274ADS50R4G NCV4274ADT50G NCV4274ADT50RKG NCV4274ST33T3G NCV4274DT33RKG NCV4274AST33T3G NCV4274ADT33RKG NCV4274ST25T3G NCV4274AST25T3G Output Voltage Accuracy 4% 4% 4% 4% 2% 2% 2% 2% 4% 4% 2% 2% 4% 2% Output Voltage 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 3.3 V 3.3 V 3.3 V 3.3 V 2.5 V 2.5 V Package D2PAK (Pb-Free) D2PAK (Pb-Free) DPAK (Pb-Free) DPAK (Pb-Free) D2PAK (Pb-Free) D2PAK (Pb-Free) DPAK (Pb-Free) DPAK (Pb-Free) SOT-223 (Pb-Free) DPAK (Pb-Free) SOT-223 (Pb-Free) DPAK (Pb-Free) SOT-223 (Pb-Free) SOT-223 (Pb-Free) Shipping 50 Units / Rail 800 / Tape & Reel 75 Units / Rail 2500 / Tape & Reel 50 Units / Rail 800 / Tape & Reel 75 Units / Rail 2500 / Tape & Reel 4000 / Tape & Reel 2500 / Tape & Reel 4000 / Tape & Reel 2500 / Tape & Reel 4000 / Tape & Reel 4000 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
13
NCV4274, NCV4274A
PACKAGE DIMENSIONS
DPAK (SINGLE GAUGE) CASE 369C-01 ISSUE O
-T- B V R
4
SEATING PLANE
C E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. INCHES MIN MAX 0.235 0.245 0.250 0.265 0.086 0.094 0.027 0.035 0.018 0.023 0.037 0.045 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.090 BSC 0.180 0.215 0.025 0.040 0.020 --- 0.035 0.050 0.155 --- MILLIMETERS MIN MAX 5.97 6.22 6.35 6.73 2.19 2.38 0.69 0.88 0.46 0.58 0.94 1.14 4.58 BSC 0.87 1.01 0.46 0.58 2.60 2.89 2.29 BSC 4.57 5.45 0.63 1.01 0.51 --- 0.89 1.27 3.93 ---
S
A
1 2 3
Z U
K F L D G
2 PL
J H 0.13 (0.005)
M
DIM A B C D E F G H J K L R S U V Z
T
SOLDERING FOOTPRINT*
6.20 0.244 3.0 0.118
2.58 0.101
5.80 0.228
1.6 0.063
6.172 0.243
SCALE 3:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
14
NCV4274, NCV4274A
PACKAGE DIMENSIONS
SOT-223 (TO-261) CASE 318E-04 ISSUE L
D b1
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. MILLIMETERS NOM MAX 1.63 1.75 0.06 0.10 0.75 0.89 3.06 3.20 0.29 0.35 6.50 6.70 3.50 3.70 2.30 2.40 0.94 1.05 1.75 2.00 7.00 7.30 10 - INCHES NOM 0.064 0.002 0.030 0.121 0.012 0.256 0.138 0.091 0.037 0.069 0.276 -
4
HE
1
2
3
E
e1
b e A q L1 C
DIM A A1 b b1 c D E e e1 L1 HE
q
MIN 1.50 0.02 0.60 2.90 0.24 6.30 3.30 2.20 0.85 1.50 6.70 0
MIN 0.060 0.001 0.024 0.115 0.009 0.249 0.130 0.087 0.033 0.060 0.264 0
MAX 0.068 0.004 0.035 0.126 0.014 0.263 0.145 0.094 0.041 0.078 0.287 10
0.08 (0003)
A1
SOLDERING FOOTPRINT
3.8 0.15 2.0 0.079
2.3 0.091
2.3 0.091
6.3 0.248
2.0 0.079 1.5 0.059
mm inches
SCALE 6:1
http://onsemi.com
15
NCV4274, NCV4274A
PACKAGE DIMENSIONS
D2PAK CASE 418AF-01 ISSUE O
NOTES: 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 4. CONTROLLING DIMENSION: INCH. 5. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 6. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 7. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.051 REF 0.100 BSC 0.539 0.579 0.125 MAX 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.295 REF 2.540 BSC 13.691 14.707 3.175 MAX 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN
-T- K A
OPTIONAL CHAMFER
TERMINAL 4
E V
U
S B F
1 2 3
H M L P
DIM A B C D E F G H J K L M N P R S U V
J D 0.010 (0.254) M T
G
N R
C
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
16
NCV4274/D

▲Up To Search▲

Price & Availability of NCV427407

	To Download NCV427407 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .